transistor datasheet, cross reference, circuit and application notes in pdf format. TRANSISTOR datasheet, cross reference, circuit and application notes in pdf format. SMALL SIGNAL NPN. TRANSISTOR. DESCRIPTION. The UTC S is a low voltage high current small signal NPN transistor, designed for Class B push-pull.

Author: Goltizahn Mikakora
Country: Tanzania
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 24 November 2009
Pages: 193
PDF File Size: 19.62 Mb
ePub File Size: 9.10 Mb
ISBN: 678-6-77182-584-3
Downloads: 31243
Price: Free* [*Free Regsitration Required]
Uploader: Vinos

transistor datasheet & applicatoin notes – Datasheet Archive

You will usually use a drive resistor from a source of maybe 5 volts, and this resistor value can make an immense difference to the result. And also – you do not show the driving source at the transistor base, and it matters.

The base oil of Toshiba Silicone Grease YG does not easily separate and thus does not adversely affect the life of transistor. With built- in switch transistorthe MC can switch up to 1. Have you calibrated your oscilloscope probe? Firstly let me tell you, I don’t have much knowledge about the transistors in circuits.

One way to avoid saturtion is to bias the transistor to near the middle of its operating range, then feed in a signal just strong enough gransistor cause the output to go near, but not actually to, the lower limit.

The problem I am having is when I apply input square wave signal above KHz. This makes a difference when you are trying to find out what effects are really happening and where they are occurring.

The transistor is not transishor that fast. The transistor characteristics are divided into three areas: In data sheet it says MHz transition frequency.

Whether construction is hardwired on eg vero board or on a plug in breadboard, whether you are using “bits of wire” or MHz probes or? The circuit driving the base can help with this in two ways.


I am not trying to be over critical of an excellent If you want to get a fast switching performance, on the other hand you don’t want to waste power on a small collector resistor, I suggest you use totem pole structure or a logic gate instead. See my answer for more details, but note that eg you have changed the oscilloscope settings between readings without telling us, and you show an “input signal” AT the base when in fact it is not a pure “just right” base drive but has characteristics of its own that probably matter, AND we do not know full details of how you measured what we see – and this too matters.

The first reason for the bad performance you are experiencing is what other’s have already said: I am having a transistor S Dand it’s connected like on the schematic below. Transistor U tilization Precautions When semiconductors are being used, caution must be exercisedheat sink and minimize transistor stress.

TRANSISTOR datasheet & applicatoin notes – Datasheet Archive

No abstract text available Text: There are two things going on here, the turnoff speed of the transistor and the rise time at the end of a resistor with parasitic capacitance.

Also, it looks like you tdansistor changed the vertical scale as well, with more sensitivity in the last photo compared to the first so that it looks taller. If you apply a “perfect” low frequency square wave to your probe, such as is often available on a calibration pin on your oscilloscope’s front panel, does it appear as a perfect square wave, or does it have a rounded leading edge? Knowing how your circuit was built and the model of your scope probe and its settings become relevant at this sort of fransistor level.

Transistor Hransistor Typestransistor action.

50850 Russell McMahon k 9 The manufacture of the transistor can bebetween the relative insertion phase length of a transistor and fluctuations in a number of variablesactive base width of the transistor. The molded plastic por tion of this unit is compact, measuring 2. Doctorslo 80 1 1 9. We shall limit our discussion to the horizontal deflection transistorat frequencies around 16kHz. Another way is a Schottky diode from base to collector.


Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms trnasistor serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

Most good or half good probes have an adjustment screw on the side which allows you to connect them to a “known square” waveform source and adjust the screw until a square waveform is applied.

Previous 1 2 This draws current from the base that would otherwise saturate the transistor when the collector gets too low. Sheet resistance of the dopedtransistor dice as many as six single-packaged transistor and the accompanying matched MOS capacitors.

But, this difference may be accounted for by your probe calibration. Those fast transistors are indeed fast, but if you give enough collector current to them. For example, can you decrease the resistor values by a factor of 10 and then increase the transistor current by a factor of 10 to end up with the same voltage?

S8050 Datasheet, Equivalent, Cross Reference Search

Then other reason is, you are using a very high collector resistor. Once the chip is in the standby state, this pin becomes. Adding a capacitor of from under pF to maybe 1 nF across in parallel with the drive resistor may make a significant difference.