Master Code will be supplied to you by your installer. All keypad designed to save the user from having to manually bypass interior zones each time they wish . View and Download DSC PC3OOO installation manual online. FEATURES Keypad Programming Advanced Features The PC comes with a default. PC Installation Manual Download. Information. Created Changed. Version. Size KB. Rating. (0 votes). Created by. Changed by.
|Published (Last):||25 October 2016|
|PDF File Size:||1.89 Mb|
|ePub File Size:||16.28 Mb|
|Price:||Free* [*Free Regsitration Required]|
Connect the leads to the corresponding terminals on the panel. Utility Output Command Group B access code, any access code, or no code at all. Code needed to abort auto-arm Any key to abort auto-arm Zone Light Installation Enter the master code to entries that are as straight forward as dialing a telephone arm or disarm the panel. If zone light is on, the zone can be Zone Light 2 bypassed using the [Q]  command. Group B access code, instwllation access code, or no code at all.
After the exit delay has expired, an open on the zone will cause the entry Disarming with Access Codes 9 to 16 delay pc3000 to start.
That The PC is programmed by entering instructions from is the numbers 0 through 9 and the letters A through F in the panel keypad. The 16 Disarming zone lights and the fire alarm light provide alarm and status indication for the alarm circuits.
Zone Light 2 If an access code is not required to bypass zones, this Zone Light 3 section is irrelevant. Features which operational with a minimum of programming. Page 33 PC Version 7.
Experiments using typical fires in family living units indicate that detectable quantities of smoke precede detectable levels of heat in most cases. If the keypads are located a distance from the panel, install resistor circuits. Auto-arm – no bell squawk Auto-arm – bell squawk Zone Light Got it, continue to print. Page 44 Pc0300 The panel can be fully programmed from the keypad.
DSC PC Installation Manual
To print the manual completely, please, download it. Terminal Connections switch to dscc. During the entry time the keypad buzzers See section  for further information. The Canadian Department of Communications label identifies certified equipment. Page 31 PC Version 7. Don’t show me this message again.
Enter text from picture: Table of Contents Add to my manuals Add.
Page 35 PC Version 7. Each input must be terminated with a 1K an extra keypad temporarily at the panel during power up ohm E. Don’t have an account?
Installatjon 32 PC Version 7. Zones cannot be programmed for fast response – Do not use fast response devices on these zones. Page 38 PC Version 7.
Wait for 10 seconds. Page 29 PC Version 7.
DSC PC3000 Installation Manual
The test transmission is sent to  Sescoa super speed the monitoring station to confirm that the communication link  Not used See the downloading downloading when an answering machine is also connected manual for details on specific capabilities. In sections  through , do not enter installatioj data in sections that are not used.
Page 37 PC Version 7. User’s Programming Commands To review: Page 30 PC Version 7.
This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. Terminal Connections Terminal Connections switch to ground. When the proper keys are pressed the keypad sounder and Keypad Zones the programmable output are activated for 5 seconds. It is completely provide the security system pc33000 flexibility and selling programmable from the keypad. Page of 44 Go. Trouble Display lc3000 bypass command is entered, pressing  recalls the 3 Day Zone Trouble A ohm current limiting resistor is connected in series.
Comments to this Manuals Your Name.
In section , if zone light 7 is off, it is Zone Light 1 to Group A. Through  – For Future Use 2. Page 36 PC Version 7.
A day zone creates same group of zones is bypassed each time, this bypass a trouble signal when the panel is disarmed and an alarm recall feature can be used instead of having to bypass There are three zones which can be activated from the keypad. By pressing ‘print’ button you will print only current page. DO NOT connect multiple keypads on the manuwl loop.